Linear Slide Components
Linear Slides can come preassembled or, alternatively, the LRE modules can be assembled on site. On this page you will find the individual components of the LRE range for onsite assembly and parts replacement.
 Shaft Clamp Profile |  Shafts |  Carriage Plates |
 Bearing Units |  Double Bearing Units |  End Cap Lubricating System |
 Rollers and Bolts |  Impact Buffers |  Preassembled Linear Units |
Common Profiles for Linear Slides
Each design will be different, however, the most common profiles used are Profile 5 20×20 or 40×20, or Profile 8 80×40 or 80×80.
Profile 5 20×20, natural
0.0.370.03
Max. L = 6000mm
Profile 5 40×20, natural
0.0.370.04
Max. L = 6000mm
Profile 8 80×40 light, natural
0.0.026.34
Max. L = 6000mm
Profile 8 80×40 heavy, natural
0.0.026.04
Max. L = 6000mm
Profile 8 80×80 light, natural
0.0.265.80
Max. L = 6000mm
Profile 8 80×80 heavy, natural
0.0.026.27
Max. L = 6000mm
Shaft Clamp Profile
The Shaft Clamp Profile is pressed into the groove of standard aluminium profile.
Shaft-Clamp Profile 5 D6, natural
0.0.390.02
Max. L = 3000mm
Shaft-Clamp Profile 8 D6, natural
0.0.356.02
Max. L = 3000mm
Shaft-Clamp Profile 8 D10, natural
0.0.442.03
Max. L = 3000mm
Shaft-Clamp Profile 8 D14, natural
0.0.294.34
Max. L = 3000mm
Shaft-Clamp Profile 8 D25, natural
0.0.350.02
Max. L = 3000mm
Shafts
The shaft is then pressed in. It is along this shaft that the carriage slides.
Shaft D6, bright
0.0.356.01
Max. L = 3000mm
Shaft D10, bright
0.0.401.09
Max. L = 6000mm
Shaft D14, bright
0.0.294.01
Max. L = 6000mm
Shaft D25, bright
0.0.350.09
Max. L = 6000mm
Carriage Plates
The object to be moved can be attached to the carriage plate using T-slot Nuts or fasteners such as Angle Brackets.
A popular choice is either the Profile 5 80×14 or Profile 8 160×28 with end caps, cut to the length required.
An ideal option for a manual slide are the pre-assembled Linear Guide Carriages. They are already equipped with bearing units. It is recommended not to use the E version of Profile 8 for these carriages.
Slide LRF can easily be automated with a Timing Belt.
Profile 5 80×14, natural
0.0.370.85
Max. L = 3000mm
Cap 5 80×14, black
0.0.370.91
Profile 8 160×28, natural
0.0.026.85
Max. L = 6000mm
Cap 8 160×28, black
0.0.026.80
Linear Guide Carriage Unit 8 D14 120×40
0.0.629.19
Linear Guide Carriage Unit 8 D14 120×80
0.0.634.63
Slide LRF 8 D10 120×160
0.0.658.32
Slide LRF 8 D10 160×160
0.0.658.37
Slide LRF 8 D14 160×160
0.0.656.27
Slide LRF 8 D14 200×160
0.0.658.21
Bearing Units
Bearing Units are the foundation of the sliding carriage. Single or Double Bearing Units are available for different uses. Two types, ‘eccentric’ and ‘centric’ differ in the geometry of the bolts to ensure the guide unit is free from play. One of each should be used.
Bearing Unit 5 D6 c
0.0.390.15
Bearing Unit 5 D6 e
0.0.390.16
Bearing Unit 8 D10 c
0.0.442.10
Bearing Unit 8 D10 e
0.0.442.09
Bearing Unit 8 D14 c
0.0.294.14
Bearing Unit 8 D14 e
0.0.294.15
Double Bearing Units
An alternative to single Bearing Units are the Double Bearing Units.
Double-Bearing Unit 5 D6 c
0.0.390.17
Double-Bearing Unit 5 D6 e
0.0.390.18
Double-Bearing Unit 8 D6 c
0.0.356.32
Double-Bearing Unit 8 D6 e
0.0.356.33
Double-Bearing Unit 8 D10 c
0.0.442.15
Double-Bearing Unit 8 D10 e
0.0.442.14
Double-Bearing Unit 8 D14 c
0.0.294.26
Double-Bearing Unit 8 D14 e
0.0.294.28
End Caps and Lubricating System
The End Cap and Lubricating System sits on the ends of the Bearing Units to prevent premature wear. The felt is saturated in oil when it leaves the factory. It is recommended to re-oil every six months.
End Cap and Lubricating System 5 D6, black
0.0.390.12
End Cap and Lubricating System 8 D6, black
0.0.356.24
End Cap and Lubricating System 8 D10, black
0.0.442.23
End Cap and Lubricating System 8 D14, black
0.0.294.46
End Cap and Lubricating System 8 D25, black
0.0.350.13
Rollers and Bolts
Suitable for building customised Bearing Units.
Roller D6
0.0.356.03
Roller D10
0.0.442.02
Roller D14
0.0.294.03
Roller D14K, black
0.0.294.52
Roller D14, stainless
0.0.488.20
Bolt 5 D6 c, bright zinc-plated
0.0.390.03
Bolt 5 D6 e, bright zinc-plated
0.0.390.19
Bolt 8 D10 c, bright zinc-plated
0.0.442.06
Bolt 8 D10 e, bright zinc-plated
0.0.442.07
Bolt 8 D14 c, bright zinc-plated
0.0.294.10
Bolt 8 D14 e, bright zinc-plated
0.0.294.12
Impact Buffers
Rubber-metal elements for absorbing impacts. Resistant to oil, water, sea water and road salt solutions. Partially resistant to soap solutions, vegetable fats and animal fats. It can also be used as a simple, damping foot.
Impact Buffer M8 D30x30, black
0.0.416.37
Impact Buffer M6 D20x15, black
0.0.416.35
Parabolic Buffer M8 D30x36, black
0.0.416.39